- 記事に戻る -
- 記事に戻る -
# dmesg
Linux version 2.4.9-31enterprise (root@sun.cobalt.com)
(gcc version 2.96 20000731 (Red Hat Linux 7.1 2.96-98))
#1 SMP vie jun 7 12:56:14 PDT 2002
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f400 (usable)
BIOS-e820: 000000000009f400 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e8000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003fff0000 (usable)
BIOS-e820: 000000003fff0000 - 000000003ffff000 (ACPI data)
BIOS-e820: 000000003ffff000 - 0000000040000000 (ACPI NVS)
BIOS-e820: 00000000fec00000 - 00000000fec02000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
Scanning bios EBDA for MXT signature
127MB HIGHMEM available.
found SMP MP-table at 000ff780
hm, page 000ff000 reserved twice.
hm, page 00100000 reserved twice.
hm, page 000f1000 reserved twice.
hm, page 000f2000 reserved twice.
On node 0 totalpages: 262128
zone(0): 4096 pages.
zone(1): 225280 pages.
zone(2): 32752 pages.
Intel MultiProcessor Specification v1.4
Virtual Wire compatibility mode.
OEM ID: INTEL Product ID: SCB20 APIC at: 0xFEE00000
Processor #3 Pentium(tm) Pro APIC version 17
Processor #0 Pentium(tm) Pro APIC version 17
I/O APIC #4 Version 17 at 0xFEC00000.
I/O APIC #5 Version 17 at 0xFEC01000.
Processors: 2
Kernel command line: BOOT_IMAGE=linux ro root=802
BOOT_FILE=/boot/vmlinuz-2.4.9-
31enterprise console=ttyS1,9600 console=tty0
Initializing CPU#0
Detected 1396.496 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 2785.28 BogoMIPS
Memory: 1026144k/1048512k available
(1890k kernel code, 20960k reserved, 103k da
ta, 244k init, 131008k highmem)
Dentry-cache hash table entries: 131072 (order: 8, 1048576 bytes)
Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
Mount-cache hash table entries: 16384 (order: 5, 131072 bytes)
Buffer-cache hash table entries: 65536 (order: 6, 262144 bytes)
Page-cache hash table entries: 262144 (order: 9, 2097152 bytes)
CPU: Before vendor init, caps: 0383fbff 00000000 00000000, vendor = 0
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 512K
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After vendor init, caps: 0383fbff 00000000 00000000 00000000
CPU: After generic, caps: 0383fbff 00000000 00000000 00000000
CPU: Common caps: 0383fbff 00000000 00000000 00000000
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
mtrr: detected mtrr type: Intel
CPU: Before vendor init, caps: 0383fbff 00000000 00000000, vendor = 0
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 512K
Intel machine check reporting enabled on CPU#0.
CPU: After vendor init, caps: 0383fbff 00000000 00000000 00000000
CPU: After generic, caps: 0383fbff 00000000 00000000 00000000
CPU: Common caps: 0383fbff 00000000 00000000 00000000
CPU0: Intel(R) Pentium(R) III CPU family 1400MHz stepping 01
per-CPU timeslice cutoff: 1462.55 usecs.
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000004
ESR value after enabling vector: 00000000
Booting processor 1/0 eip 2000
Initializing CPU#1
masked ExtINT on CPU#1
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Calibrating delay loop... 2791.83 BogoMIPS
CPU: Before vendor init, caps: 0383fbff 00000000 00000000, vendor = 0
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 512K
Intel machine check reporting enabled on CPU#1.
CPU: After vendor init, caps: 0383fbff 00000000 00000000 00000000
CPU: After generic, caps: 0383fbff 00000000 00000000 00000000
CPU: Common caps: 0383fbff 00000000 00000000 00000000
CPU1: Intel(R) Pentium(R) III CPU family 1400MHz stepping 01
Total of 2 processors activated (5577.11 BogoMIPS).
ENABLING IO-APIC IRQs
...changing IO-APIC physical APIC ID to 4 ... ok.
...changing IO-APIC physical APIC ID to 5 ... ok.
init IO_APIC IRQs
IO-APIC (apicid-pin) 4-0, 4-5, 4-7, 4-9, 4-11,
5-0, 5-1, 5-3, 5-6, 5-7, 5-8, 5-
9, 5-12, 5-13, 5-14, 5-15 not connected.
..TIMER: vector=0x31 pin1=2 pin2=0
..MP-BIOS bug: 8254 timer not connected to IO-APIC
...trying to set up timer (IRQ0) through the 8259A ...
..... (found pin 0) ...works.
number of MP IRQ sources: 17.
number of IO-APIC #4 registers: 16.
number of IO-APIC #5 registers: 16.
testing the IO APIC.......................
IO APIC #4......
.... register #00: 04000000
....... : physical APIC id: 04
.... register #01: 000F0011
....... : max redirection entries: 000F
....... : IO APIC version: 0011
.... register #02: 00000000
....... : arbitration: 00
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 003 03 0 0 0 0 1 1 1 31
01 003 03 0 0 0 0 0 1 1 39
02 000 00 1 0 0 0 0 0 0 00
03 003 03 0 0 0 0 0 1 1 41
04 003 03 0 0 0 0 0 1 1 49
05 000 00 1 0 0 0 0 0 0 00
06 003 03 0 0 0 0 0 1 1 51
07 000 00 1 0 0 0 0 0 0 00
08 003 03 0 0 0 0 0 1 1 59
09 000 00 1 0 0 0 0 0 0 00
0a 003 03 1 1 0 1 0 1 1 61
0b 000 00 1 0 0 0 0 0 0 00
0c 003 03 0 0 0 0 0 1 1 69
0d 003 03 0 0 0 0 0 1 1 71
0e 003 03 0 0 0 0 0 1 1 79
0f 003 03 0 0 0 0 0 1 1 81
IO APIC #5......
.... register #00: 05000000
....... : physical APIC id: 05
.... register #01: 000F0011
....... : max redirection entries: 000F
....... : IO APIC version: 0011
.... register #02: 08000000
....... : arbitration: 08
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 000 00 1 0 0 0 0 0 0 00
01 000 00 1 0 0 0 0 0 0 00
02 003 03 1 1 0 1 0 1 1 89
03 000 00 1 0 0 0 0 0 0 00
04 003 03 1 1 0 1 0 1 1 91
05 003 03 1 1 0 1 0 1 1 99
06 000 00 1 0 0 0 0 0 0 00
07 000 00 1 0 0 0 0 0 0 00
08 000 00 1 0 0 0 0 0 0 00
09 000 00 1 0 0 0 0 0 0 00
0a 003 03 1 1 0 1 0 1 1 A1
0b 003 03 1 1 0 1 0 1 1 A9
0c 000 00 1 0 0 0 0 0 0 00
0d 000 00 1 0 0 0 0 0 0 00
0e 000 00 1 0 0 0 0 0 0 00
0f 000 00 1 0 0 0 0 0 0 00
IRQ to pin mappings:
IRQ0 -> 0:2
IRQ1 -> 0:1
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ6 -> 0:6
IRQ8 -> 0:8
IRQ10 -> 0:10
IRQ12 -> 0:12
IRQ13 -> 0:13
IRQ14 -> 0:14
IRQ15 -> 0:15
IRQ18 -> 1:2
IRQ20 -> 1:4
IRQ21 -> 1:5
IRQ26 -> 1:10
IRQ27 -> 1:11
.................................... done.
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 1396.4548 MHz.
..... host bus clock speed is 132.9955 MHz.
cpu: 0, clocks: 1329955, slice: 443318
CPU0<T0:1329952,T1:886624,D:10,S:443318,C:1329955>
cpu: 1, clocks: 1329955, slice: 443318
CPU1<T0:1329952,T1:443312,D:4,S:443318,C:1329955>
checking TSC synchronization across CPUs: passed.
PCI: PCI BIOS revision 2.10 entry at 0xfdb65, last bus=2
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Discovered primary peer bus 01 [IRQ]
PCI: Discovered primary peer bus 02 [IRQ]
PCI: Using IRQ router default [1166/0201] at 00:0f.0
PCI->APIC IRQ transform: (B0,I3,P0) -> 21
PCI->APIC IRQ transform: (B0,I4,P0) -> 20
PCI->APIC IRQ transform: (B0,I12,P0) -> 18
PCI->APIC IRQ transform: (B0,I15,P0) -> 10
PCI->APIC IRQ transform: (B0,I15,P0) -> 10
PCI->APIC IRQ transform: (B1,I7,P0) -> 27
PCI->APIC IRQ transform: (B1,I7,P1) -> 26
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
apm: BIOS not found.
mxt_scan_bios: enter
Starting kswapd v1.8
allocated 256 pages and 256 bhs reserved for the highmem bounces
VFS: Diskquotas version dquot_6.5.0 initialized
Detected PS/2 Mouse Port.
pty: 2048 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08)
with MANY_PORTS MULTIPORT SHARE_IRQ SER
IAL_PCI ISAPNP enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
Real Time Clock Driver v1.10e
block: queued sectors max/low 680557kB/549485kB, 2048 slots per queue
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz PCI bus speed for PIO modes; override with idebus=xx
ServerWorks CSB5: IDE controller on PCI bus 00 dev 79
PCI: Device 00:0f.1 not available because of resource collisions
ServerWorks CSB5: chipset revision 146
ServerWorks CSB5: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x03a0-0x03a7, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0x03a8-0x03af, BIOS settings: hdc:pio, hdd:pio
hda: SAMSUNG CD-ROM SN-124, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Floppy drive(s): fd0 is 1.44M
FDC 0 is a National Semiconductor PC87306
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
pci_hotplug: PCI Hot Plug PCI Core version: 0.3
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 8192 buckets, 64Kbytes
TCP: Hash tables configured (established 262144 bind 65536)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 450k freed
VFS: Mounted root (ext2 filesystem).
SCSI subsystem driver Revision: 1.00
(scsi0) <Adaptec AIC-7899 Ultra 160/m SCSI host adapter> found at PCI 1/7/0
(scsi0) Wide Channel A, SCSI ID=7, 32/255 SCBs
(scsi0) Downloading sequencer code... 396 instructions downloaded
(scsi1) <Adaptec AIC-7899 Ultra 160/m SCSI host adapter> found at PCI 1/7/1
(scsi1) Wide Channel B, SCSI ID=7, 32/255 SCBs
(scsi1) Downloading sequencer code... 396 instructions downloaded
scsi0 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 5.2.4/5.2.0
<Adaptec AIC-7899 Ultra 160/m SCSI host adapter>
scsi1 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 5.2.4/5.2.0
<Adaptec AIC-7899 Ultra 160/m SCSI host adapter>
blk: queue f7d36c18, I/O limit 4095Mb (mask 0xffffffff)
blk: queue f7d36c18, I/O limit 4095Mb (mask 0xffffffff)
Vendor: SEAGATE Model: ST373405LC Rev: 0003
Type: Direct-Access ANSI SCSI revision: 03
blk: queue f76b4e18, I/O limit 4095Mb (mask 0xffffffff)
Vendor: ESG-SHV Model: SCA HSBP M18 Rev: 0.07
Type: Processor ANSI SCSI revision: 02
blk: queue f76b4218, I/O limit 4095Mb (mask 0xffffffff)
Attached scsi disk sda at scsi1, channel 0, id 0, lun 0
(scsi1:0:0:0) Synchronous at 160.0 Mbyte/sec, offset 63.
SCSI device sda: 143374741 512-byte hdwr sectors (73408 MB)
Partition check:
sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 >
Journalled Block Device driver loaded
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Freeing unused kernel memory: 244k freed
Adding Swap: 923696k swap-space (priority -1)
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-ohci.c: USB OHCI at membase 0xf88e4000, IRQ 10
usb-ohci.c: usb-00:0f.2, ServerWorks OSB4/CSB5 OHCI USB Controller
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 4 ports detected
EXT3 FS 2.4-0.9.11, 3 Oct 2001 on sd(8,2), internal journal
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.11, 3 Oct 2001 on sd(8,7), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.11, 3 Oct 2001 on sd(8,6), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.11, 3 Oct 2001 on sd(8,3), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
NET4: Linux IPX 0.47 for NET4.0
IPX Portions Copyright (c) 1995 Caldera, Inc.
IPX Portions Copyright (c) 2000, 2001 Conectiva, Inc.
NET4: AppleTalk 0.18a for Linux NET4.0
eepro100.c:v1.09j-t 9/29/99 Donald Becker
http://cesdis.gsfc.nasa.gov/linux/drivers/eepro100.html
eepro100.c: $Revision: 1.36 $ 2000/11/17 Modified by Andrey V. Savochkin
<saw@saw.sw.com.sg>
and others
eth0: OEM i82557/i82558 10/100 Ethernet, 00:03:47:F1:52:0F, IRQ 21.
Board assembly fab600-000, Physical connectors present: RJ45
Primary interface chip i82555 PHY #1.
General self-test: passed.
Serial sub-system self-test: passed.
Internal registers self-test: passed.
ROM checksum self-test: passed (0xb874c1d3).
eth1: OEM i82557/i82558 10/100 Ethernet, 00:03:47:F1:52:10, IRQ 20.
Board assembly fab600-000, Physical connectors present: RJ45
Primary interface chip i82555 PHY #1.
General self-test: passed.
Serial sub-system self-test: passed.
Internal registers self-test: passed.
ROM checksum self-test: passed (0xb874c1d3).
eth1: 0 multicast blocks dropped.
iSCSI version 2.0.1.8 ( 8-Aug-2001)
iSCSI control device major number 254
iSCSI: detected HBA f6bb313c, host #2
scsi2 : iSCSI (2.0.1.8)
|
